2 Slot Drain
2021年3月5日Register here: http://gg.gg/ojwyp
*Trench Drain
*2 Slot Drain Cleaner
*2 Slot Drain Pipe
Chapter 9-1 of 70 Chapter 9 - Storm Drains 9.1 Introduction 9.1.1 Objective This chapter provides guidance on storm drain design and analysis. The quality of the. Duraslot is made from dual-wall corrugated polyethylene pipe with an aluminum slot mounted on top of 4’ - 36’ (10.16cm - 91.44cm) N-12 pipe. Typical applications include roadways, sidewalks, parking lots, plazas, loading docks, industrial floors, parks and athletic fields. Typically a 1.5’ flat surface to each side of the slot drain is sufficient. Generally after the sink is installed in place, silicone is all that is needed to install the Drain Pan to the bottom of the sink. If necessary, secure the drain pan to the sink using screws or strapping. Brickslot System Nominal wheel load Pavers pavers to edge Concrete haunch to top; Brickslot 100: K100 (Gal rail) 2,670kg: Brickslot 100: K100 (Gal rail) 8,000kg.Scope
This specification describes 4- through 36-inch (100 to 900 mm) ADS DURASLOT pipe for use in surface drain applications.Pipe RequirementsTrench Drain
DURASLOT pipe, as manufactured and distributed by ADS, Inc., shall have a smooth interior and annular exterior corrugations with an aluminum slot grate frame mounted longitudinally along the length of the pipe to accept the grate while maintaining the original pipe diameter..
*4- through 10-inch (100 to 250mm) pipe shall meet AASHTO M252, Type S.
*12- through 36-inch (300 to 900 mm) pipe shall meet AASHTO M294, Type S or ASTM F2306.
*Manning’s “n” value for use in design shall be 0.012.
The aluminum slot grate frame shall be manufactured from 0.063” tempered commercial aluminum meeting the requirements of ASTM B209, consisting of two parallel plates separated by spacers spanning the slot on 6” centers. The grate shall be ½ - #13 galvanized steel. The grate shall have a diamond-shaped opening and be ADA compliant. The flange at the bottom of the aluminum slot grate frame shall be riveted to the pipe with a minimum of two rivets per linear foot.2 Slot Drain Cleaner2 Slot Drain PipeFittings
DURASLOT fittings shall be modified from fittings which conform to AASHTO M252, AASHTO M294, or ASTM F2306.Installation
Installation shall be in accordance with ADS recommended installation instructions. Contact your local ADS representative or visit www.ads-pipe.com for a copy of the latest installation guidelines.
Register here: http://gg.gg/ojwyp
https://diarynote-jp.indered.space
*Trench Drain
*2 Slot Drain Cleaner
*2 Slot Drain Pipe
Chapter 9-1 of 70 Chapter 9 - Storm Drains 9.1 Introduction 9.1.1 Objective This chapter provides guidance on storm drain design and analysis. The quality of the. Duraslot is made from dual-wall corrugated polyethylene pipe with an aluminum slot mounted on top of 4’ - 36’ (10.16cm - 91.44cm) N-12 pipe. Typical applications include roadways, sidewalks, parking lots, plazas, loading docks, industrial floors, parks and athletic fields. Typically a 1.5’ flat surface to each side of the slot drain is sufficient. Generally after the sink is installed in place, silicone is all that is needed to install the Drain Pan to the bottom of the sink. If necessary, secure the drain pan to the sink using screws or strapping. Brickslot System Nominal wheel load Pavers pavers to edge Concrete haunch to top; Brickslot 100: K100 (Gal rail) 2,670kg: Brickslot 100: K100 (Gal rail) 8,000kg.Scope
This specification describes 4- through 36-inch (100 to 900 mm) ADS DURASLOT pipe for use in surface drain applications.Pipe RequirementsTrench Drain
DURASLOT pipe, as manufactured and distributed by ADS, Inc., shall have a smooth interior and annular exterior corrugations with an aluminum slot grate frame mounted longitudinally along the length of the pipe to accept the grate while maintaining the original pipe diameter..
*4- through 10-inch (100 to 250mm) pipe shall meet AASHTO M252, Type S.
*12- through 36-inch (300 to 900 mm) pipe shall meet AASHTO M294, Type S or ASTM F2306.
*Manning’s “n” value for use in design shall be 0.012.
The aluminum slot grate frame shall be manufactured from 0.063” tempered commercial aluminum meeting the requirements of ASTM B209, consisting of two parallel plates separated by spacers spanning the slot on 6” centers. The grate shall be ½ - #13 galvanized steel. The grate shall have a diamond-shaped opening and be ADA compliant. The flange at the bottom of the aluminum slot grate frame shall be riveted to the pipe with a minimum of two rivets per linear foot.2 Slot Drain Cleaner2 Slot Drain PipeFittings
DURASLOT fittings shall be modified from fittings which conform to AASHTO M252, AASHTO M294, or ASTM F2306.Installation
Installation shall be in accordance with ADS recommended installation instructions. Contact your local ADS representative or visit www.ads-pipe.com for a copy of the latest installation guidelines.
Register here: http://gg.gg/ojwyp
https://diarynote-jp.indered.space
コメント